List of products by brand Ultimate Racing

Carbon fiber servo spacer 1mm Ultimate Racing
In Stock
This is a pack of four optional Ultimate Racing 1mm Carbon Fiber Servo Spacers. They provide your servo with a rigid mounting surface to ensure that your servo stays tight and the screws do not loosen as the plastic shims compress over time. They are intended for some servos that are taller than others to prevent them from hitting the chassis by raising them 1mm.
Quantity: 4 pcs
5 1
5 5
Out-of-Stock
Front Rear Lower B arm mount Mugen MBX8/8R Ultimate
Out-of-Stock
It is machined from T6-7075 aluminum and anodized in dark gray. It is 7mm thick, and the original Mugen is 5mm, greater robustness.
Specifically designed to prevent breakage of the arm mount bushing. This is achieved because the bushing rests entirely on the arm mount, so when the car receives a front impact, the pin will never pierce the bushing. Even though this area has been reinforced, a small hole has been left where the bushing rests so that we can see in which position it is mounted.
5 1
5 5
Closed wheel nuts 17mm Ultimate Racing
In Stock
For 1/8 wheels (Buggy, Truggy, Monster Truck).
Specs:- Its closed end design helps protect the wheel hex from impact.- Super lightweight design following the aesthetics of the wheel hex.- All the apexes of the nut include a chamfer that helps to fit the nut more quickly and easily with the wheel wrench.- The part in contact with the rim is knurled for a better grip.
Package includes 4 nuts.
5 1
5 5
Wheel hex set +0/1/2mm Lightweight Set Ultimate Racing
In Stock
This is the Ultimate Racing Lightweight 0mm, +1mm and +2mm Wheel Hexagon Set. They are machined from T6-7075 Aluminum and anodized in dark gray. Intended for Mugen, Associated, Xray, Sworkz, Losi and Tekno among others.
Thanks to its design, its weight has been lightened about 25% compared to the original Mugen ones.
All the apexes of the hexagon have a chamfer that helps to make wheel changes faster and easier.
5 1
5 5
Wheel hex set 0mm Lightweight Ultimate Racing
In Stock
This is the Ultimate Racing Lightweight 0mm Wheel Hexagon. It is machined from T6-7075 Aluminum and anodized in dark gray.
Intended for: Mugen, Associated, Xray, Sworkz, Losi and Tekno among others.
Thanks to its design, its weight has been lightened about 25% compared to the original Mugen ones.
All the apexes of the hexagon have a chamfer that helps to make wheel changes faster and easier.
Quantity: 2 pcs
5 1
5 5
Out-of-Stock
Wheel hex set 1mm Lightweight Ultimate Racing
Out-of-Stock
This is the Ultimate Racing Lightweight +1mm Wheel Hexagon. It is machined from T6-7075 Aluminum and anodized in dark gray.
Intended for: Mugen, Associated, Xray, Sworkz, Losi and Tekno among others.
Thanks to its design, its weight has been lightened about 25% compared to the original Mugen ones.
All the apexes of the hexagon have a chamfer that helps to make wheel changes faster and easier.
Quantity: 2 pcs
5 1
5 5
Wheel hex set 2mm Lightweight Ultimate Racing
In Stock
This is the Ultimate Racing Lightweight +2mm Wheel Hexagon. It is machined from T6-7075 Aluminum and anodized in dark gray.
Intended for: Mugen, Associated, Xray, Sworkz, Losi and Tekno among others.
Thanks to its design, its weight has been lightened about 25% compared to the original Mugen ones.
All the apexes of the hexagon have a chamfer that helps to make wheel changes faster and easier.
Quantity: 2 pcs
5 1
5 5
Vented steel brake disks Ultimate Racing
In Stock
Vented steel brake disks intended for Mugen and Sworkz among others.
Thanks to the holes and slots we get a lower temperature which results in less wear and a more uniform braking feel.
Due to these grooves, we also achieve significant weight savings. The Ultimate brake discs are 30% lighter than the original Mugen discs. This weight savings in rotational mass translates into faster acceleration and lower fuel consumption.
Quantity: 2 pcs
5 1
5 5
Aluminum ball link protector Ultlimate Racing
In Stock
This is the Ultimate Racing Aluminum Steering Ball Link Protector. It is machined from T6-7075 aluminum and anodized in dark gray.
Designed to fit the ball link to prevent the rims from rubbing when turning the wheels and weakening the ball link.
Quantity: 2 pcs
Mounting: No glue is required. Place the protectors as far as possible inside the ball joints and thread the tie rod. As the tie rod is threaded, the plastic of the ball joint expands, locking the protector in place.
5 1
5 5
Out-of-Stock
Aluminum front center 84.5mm driveshaft Ultimate Racing
Out-of-Stock
It is machined from T6-7075 aluminum and anodized in dark gray.
Being made of aluminum and not steel as the original Mugen, we get more flexibility. This extra flexibility translates into greater traction while smoothing the reactions of the car when accelerating.
In addition, we lighten its weight since the aluminum ones weigh 50% less than the original Mugen steel ones. This rotational weight savings translates into lower fuel consumption and faster acceleration.
5 1
5 5
Aluminum center rear 115mm driveshaft Ultimate Racing
In Stock
This is the 115cm Aluminum Rear Centre Driveshaft from Ultimate Racing. It is machined from T6-7075 aluminum and anodized in dark gray.
Being made of aluminum and not steel as the original Mugen, we get more flexibility. This extra flexibility translates into greater traction while smoothing the reactions of the car when accelerating.
5 1
5 5
Front shock tower Mugen MBX8R Carbon Fiber
In Stock
This is the optional Ultimate Racing Carbon Front Shock Tower intended for the Mugen MBX8R.
Features:- Made from 4mm thick 100% high density and flexibility carbon fiber.- It only weights 16gr. Lighter than the 26gr of the original aluminum, lowering the center of gravity.- Machined to avoid friction with the shocks.
Same geometry as the Mugen original.
5 1
5 5
Rear shock tower Mugen MBX8R Carbon Fiber
In Stock
Features:- Made from 4mm thick 100% high density and flexibility carbon fiber.- It only weights 21gr. Lighter than the 33gr of the original aluminum, lowering the center of gravity.- 2 extra holes for the upper arm that allow you to raise the roll center.- 1 extra hole for lowering the rear body mount at hi-speed tracks.
5 1
5 5
Battery box carbon fiber cover Mugen MBX8R
In Stock
Features:- Made from 3mm thick 100% bright high density carbon fiber with same appearance than the Mugen carbon radio tray.- It perfectly fits on the battery box to protect its interior against dust.- Interior machined to better fit on the battery box and be able to use most of the receiver batteries.
5 1
5 5